RXRacing

Howerton decals

admin — Tue, 01 May 2012 16:13:59 +0000

I’ve received the decals from my sponsor, Howerton Engineering. Jeff set me up with an amazing Aquamist system. Unlike most systems, Aquamist uses a PWM driver and uses the fuel injector signal to control the metering. Since HP produced has a direct relationship with fuel input, this is hands down the most logical way to keep an optimal mix going. With Jeff Howerton’s slosh control tank, the system performs flawlessly under very demanding road racing conditions. Hit Jeff up for a system if you want a bulletproof meth/water injection system.

Diff rebuilt with 4.30 gears

admin — Sun, 29 Apr 2012 21:15:58 +0000

Ford explorer diff+ Ronin mount. Pretty much ready to press in the Delrin bushings and test fit.

Also got in replacement rotors for my three year old set. 12.9″ x 1.25″, same as last time. Directionally vented for better cooling

Three and four done

admin — Thu, 26 Apr 2012 16:56:22 +0000

Now both axles are finished and back together. Now I just need to cut up the rear cover and mount the new cradle and the diff should be ready to go in. I’ll have to build yet another driveshaft. Aluminum or Carbon Fiber? Always the question.

Two CV’s ha ha ha

admin — Mon, 23 Apr 2012 00:01:27 +0000

Got the Ford inner on the custom axle. All booted up. Now just one more axle

One CV ha ha ha

admin — Sun, 22 Apr 2012 23:11:47 +0000

Well I now have the explorer diff rebuilt with the Ford Racing carbon LSD clutch pack. Thanks Ryan. I’ve also manages to clean, repack and install one of the outer CV’s on the drive axle

Update: Looks like the differential isn’t doing very well.

admin — Sat, 04 Feb 2012 00:41:32 +0000

During the Indy I had a lot of smoke before the transmission blew up. It turns out the freeze plug-style inspection cover had popped off and was allowing some fluid to drop onto the driveshaft. I also had both dust boots on the inner CV’s develop large rips. I think the 155 mph top speed had something to do with that.

Along with replacing the CV boots I pulled the diff apart to inspect it and saw some troubling wear on the gear teeth. Since there wasn’t a lot of filings in the fluid I think the problem is heat related and I’ve decided upon an upgrade to the Ford 8.8 differential (the $200 cost for ring gear replacement in the 8.8 vs the $650 for Mazda rind gears had a lot to do with the decision, as did the wide variety of available ratios for the Ford 8.8). I’ve located a low mileage 8.8 locally and I’ve purchased an 8.8 explorer mount kit from Ronin Speedworks (http://www.roninspeedworks.com/powertrain/) and I’m trying to line up a good cooling option for both the diff and transmission to increase the longevity of both parts.

New pictures from the Indy

admin — Thu, 10 Nov 2011 21:48:58 +0000

I’ve just managed to get and review the images my photographer took at the 2011 Indy. In a few of the shots you can see the smoke coming our of the car as the gearbox strats to puke fluid onto the exhaust.

Transmission is fixed

admin — Fri, 23 Sep 2011 22:38:18 +0000

After tearing third gear to little bits at the Edmonton Indy, we pulled the transmission out of the car to assess the damage. The transmission is a T5 with a G-Force straight cut dog-engaged gearset and the damage was bad. Third gear was toast on both the mainshaft and countershaft. As well, the countershaft bearings had oblonged the case. I had to buy new gears, new bearings and seals and a new case. It is all back together now and ready to go back in the car.

Indy

admin — Tue, 26 Jul 2011 01:05:06 +0000

Well, another Indy is over. The car was working great and the speed was impressive, but the reliability wasn’t there this year. With five minutes remaining in the race I broke the transmission. Plan is to pull it apart sometime in the near future and see what all the grinding noises are about.

-Trent

Aquamist is in

admin — Thu, 21 Jul 2011 05:07:09 +0000

After a late night thrash I managed to get the Aquamist water injection system in. Since it is a race car, I wired the injector signal to the secondaries and turned up the gain. During testing I was able to push to 19 PSI with EGT’s in the 1450 range. Previous 17 PSI attempts had EGTs over 1650. I think this setup will be a large benefit at the Indy.